taking off and running up to speed, not much bow rise
https://youtu.be/R6cZ1F9-J1E
Search found 104 matches
- Sun May 01, 2022 11:35 pm
- Forum: Your Alloy Boat
- Topic: pacific assassin build
- Replies: 95
- Views: 39530
- Sun May 01, 2022 11:34 pm
- Forum: Your Alloy Boat
- Topic: pacific assassin build
- Replies: 95
- Views: 39530
Re: pacific assassin build
short video of trying to blow out the props in a turn or getting some sliding
https://youtu.be/kGg2GfD7OaI
https://youtu.be/kGg2GfD7OaI
- Sun May 01, 2022 11:33 pm
- Forum: Your Alloy Boat
- Topic: pacific assassin build
- Replies: 95
- Views: 39530
Re: pacific assassin build
I got the 2 hrs of break in time at 3k rpm and the one hr of 4k rpm done this weekend. Now I can run it up to max rpm as long as its not for longer then 5 min. and vary the speed fo rthe next seven hrs. So I have some numbers Ok I am running 15x22 Solas 4 blades. 2500 RPM's was around 15 mph at 2.8 ...
- Sun May 01, 2022 11:30 pm
- Forum: Your Alloy Boat
- Topic: pacific assassin build
- Replies: 95
- Views: 39530
Re: pacific assassin build
got the call and had to go fight the portland traffic on the way home
- Sun May 01, 2022 11:29 pm
- Forum: Your Alloy Boat
- Topic: pacific assassin build
- Replies: 95
- Views: 39530
Re: pacific assassin build
while I was waiting for motors to be installed I made a bit more progress on the bait prep table
- Sun May 01, 2022 11:27 pm
- Forum: Your Alloy Boat
- Topic: pacific assassin build
- Replies: 95
- Views: 39530
Re: pacific assassin build
starting to work on the bait prep table. Will have a UMHW base to protect knife edges. Will not mount it untill motors are mounted so that it is not too low and gets hit by motors. will also figure out where the drains will go so that it does not puke it all over the motor
- Sun May 01, 2022 11:26 pm
- Forum: Your Alloy Boat
- Topic: pacific assassin build
- Replies: 95
- Views: 39530
Re: pacific assassin build
ook her down to fill here up with fuel, only a 190 gallons instead of the 200 that I was hoping for lol. That will work, took quite a few times when the pump would only allow $100 at a time. Brought her back home and gave her a quick bath.
- Tue Mar 29, 2022 12:06 am
- Forum: Your Alloy Boat
- Topic: pacific assassin build
- Replies: 95
- Views: 39530
Re: pacific assassin build
built a base mount for the bleed bucket, I will strap the top to the hand rails
I did not want it there full time so I built some tabs for it to bolt it down when HOPEFULLY needed for tuna season
I did not want it there full time so I built some tabs for it to bolt it down when HOPEFULLY needed for tuna season
- Tue Mar 29, 2022 12:02 am
- Forum: Your Alloy Boat
- Topic: pacific assassin build
- Replies: 95
- Views: 39530
Re: pacific assassin build
so Suzuki and Furuno have combined with a new feature called fishhunter drive. It has a couple of great options that I wanted. Only available with APC4 motors, Furuno Navpilot 300 and SPC 2.0 controls. I had the SPC 1.0 controls so to get those two (point lock and sabaki lock) I had to upgrade contr...
- Thu Mar 10, 2022 11:59 pm
- Forum: Your Alloy Boat
- Topic: pacific assassin build
- Replies: 95
- Views: 39530
Re: pacific assassin build
two rod holders on the back deck, I will have to run leashes with these style rod holders.
The rod holders only hang outside the boat 2.5"
front rod holders, one right by the cabin so it will be close to hand while driving the boat.
The rod holders only hang outside the boat 2.5"
front rod holders, one right by the cabin so it will be close to hand while driving the boat.
- Thu Mar 10, 2022 11:56 pm
- Forum: Your Alloy Boat
- Topic: pacific assassin build
- Replies: 95
- Views: 39530
Re: pacific assassin build
new back rail, I moved the right sided over a couple inches to match up with the transom door rail.
transom door rail and a pole holder on the rail
transom door rail and a pole holder on the rail
- Thu Mar 10, 2022 8:55 am
- Forum: Your Alloy Boat
- Topic: pacific assassin build
- Replies: 95
- Views: 39530
Re: pacific assassin build
She is coming along GREAT, nice work on the rails. You better be careful or Julie will make you come to work for Pacific. Thanks :), and Julie and crew will get to see it here in a couple of weeks as I am going to have them open up the wire gutter (below deck 4" square tubing) on the Port si...
- Thu Mar 10, 2022 8:50 am
- Forum: Your Alloy Boat
- Topic: pacific assassin build
- Replies: 95
- Views: 39530
Re: pacific assassin build
noex'2, A couple remarks about bending 6061 T6 pipe. As the pipe is pulled by one part of the bender around the shaped inner die- most pipe will deform at the two edges of the die- if 12:00 if up and 6:00 is inside the bottom die the 3:00 & 9:00 are the top edges of the die. This 'egging' or ...
- Thu Mar 03, 2022 10:59 pm
- Forum: Your Alloy Boat
- Topic: pacific assassin build
- Replies: 95
- Views: 39530
Re: pacific assassin build
From the add on fleabay. Mine spins at 84 RPM FSNL. 200w/12a = 16.66 amps continuous amps 1200w/12a = 100amps peak. these are at 12V The plastic covers and brake assembly's were removed and ends of the wires were stripped ready to hook to the controller of your choice. These are brushed dc motors. 2...
- Thu Mar 03, 2022 8:51 pm
- Forum: Your Alloy Boat
- Topic: pacific assassin build
- Replies: 95
- Views: 39530
Re: pacific assassin build
Can't wait to see this working on the water. What's the amp draw on the motor and are you going to carry a small generator on the boat ? Cannot wait to get motors to get it on the water lol. I will check on the amp draw, I am just going to use the house battery. I had Pacific mount a spot for a s...
- Thu Mar 03, 2022 8:48 pm
- Forum: Your Alloy Boat
- Topic: pacific assassin build
- Replies: 95
- Views: 39530
Re: pacific assassin build
Holy cow it bent in one shot with no issues. Looks like I used up all my luck for the day, no use to buy lottery tickets now lol.
- Thu Mar 03, 2022 8:46 pm
- Forum: Your Alloy Boat
- Topic: pacific assassin build
- Replies: 95
- Views: 39530
Re: pacific assassin build
with the taller side rails the 3.25" tall back rail looks funny and I would like a little more height there anyway so it is going to get cut out. I also am going to add a rail to the transom door also
- Thu Mar 03, 2022 8:45 pm
- Forum: Your Alloy Boat
- Topic: pacific assassin build
- Replies: 95
- Views: 39530
Re: pacific assassin build
Getting to the fun stuff lol I wanted the sides of the boat to be a little higher so I added some 6" tall rails. This is made with 1.25" pipe (1.66" OD) the same as Pacific used up front. Glad I have the die for that for my bender. The only poblem is that the 1.25" OD pipe I can ...
- Mon Feb 28, 2022 9:17 pm
- Forum: Your Alloy Boat
- Topic: pacific assassin build
- Replies: 95
- Views: 39530
Re: pacific assassin build
finished up the pot puller, I made it into a 3 piece setup. The motor is a a (Jazzy) wheel chair motor from Ebay($40 shipped). I had the pulley and motor base machined for free from a buddy, Yeh I owe him a few trips lol. All in I am in it less then couple hundred bucks, hope it works on the water. ...
- Wed Feb 23, 2022 2:50 am
- Forum: Your Alloy Boat
- Topic: pacific assassin build
- Replies: 95
- Views: 39530
Re: pacific assassin build
Great pictures, AWESOME shop and clean work. How are you getting power to the Davit? Thanks and I have a power outlet on the cabin right next to where the davit sits. I will just run the power cable across. And since I like projects, I am using a wheel chair motor for the davit puller motor. 2022...
- Tue Feb 22, 2022 1:38 am
- Forum: Your Alloy Boat
- Topic: pacific assassin build
- Replies: 95
- Views: 39530
Re: pacific assassin build
installing the davit, measure twice and cut once lol. 3" schedule 40. It was a pain trying to drill the lower holes with the holesaw, not much room and it sucked when it would grab a tooth. I installed it in the gunnel to give me as much room down the walkway as I can get. 20220221_125956-1.jp...
- Tue Feb 22, 2022 1:29 am
- Forum: Your Alloy Boat
- Topic: pacific assassin build
- Replies: 95
- Views: 39530
Re: pacific assassin build
back of the dash panel
the auto pilot control and NMEA2k network
- Tue Feb 22, 2022 1:26 am
- Forum: Your Alloy Boat
- Topic: pacific assassin build
- Replies: 95
- Views: 39530
Re: pacific assassin build
more wiring fun, main bonding bus in upper left corner with Suzuki gateway rigth underneath it. There is room for the second one right below. The ecm and the rest of the Suzuki wiring is on the upper right hand side. Cannot tighen and straighen the wires in this area till the motors are installed. 2...
- Tue Feb 22, 2022 1:22 am
- Forum: Your Alloy Boat
- Topic: pacific assassin build
- Replies: 95
- Views: 39530
Re: pacific assassin build
lots of wires coming out of the gutter from the transom. WIsh I would have had Pacific open the other side up also. Two of the breakers feed the reel outlets on the cabin, one for the pot davit motor, and one feeds the transom power distribution panel for the reel outlets on the back deck. Oh yeh an...
- Tue Feb 22, 2022 1:21 am
- Forum: Your Alloy Boat
- Topic: pacific assassin build
- Replies: 95
- Views: 39530
Re: pacific assassin build
Autopilot pump, shut off valves installed so I can lock out the pump if there are issues with the pump. The handles are zip tied up. I also installed the Furuno Safe helm2 in the line heading up to steering wheel. Pacific installed the mounting plate for me, make life a little easier. 20220220_20304...