Please advice on homemade dive plateform can I JB cold weld glue
I’ve bolted and revited diamondplate though the tube it stiffenes up the diamond plate.
I currentely have one triangle surport second isn’t pictured, even though the cut triangle is grinded smooth I’ll bend it over.
Will be bending a tube grab handle then bolt top to transome cap bottom bolts the plate.
Sinces it is already very sturdie curious if I can get away using I JB cold weld glue to smooth over inbetween plate and tube and probablley glue where I bend over the triangles?
designed this to hold a extra large cooler w/ around 200Lbs of fish ice, or a upto 19 gallon external fuel tank, will be used to hold catch retrial stuff when diving.
Thanks
Please advice on homemade dive plateform can I JB cold weld glue
-
- Posts: 22
- Joined: Wed Mar 01, 2017 8:31 am
- 7
-
- Posts: 22
- Joined: Wed Mar 01, 2017 8:31 am
- 7
Re: Please advice on homemade dive plateform can I JB cold weld glue
[image][/image]is it possiable to post images here? I know how to upload a attached image unsure of the procedure here I click image and image is in parenthesis.[album][/album]
-
- Posts: 22
- Joined: Wed Mar 01, 2017 8:31 am
- 7
-
- Donator 08, 09, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24
- Posts: 1751
- Joined: Mon Aug 18, 2008 1:37 am
- 15
- Your location: Kenai, AK
- Location: Kenai, Alaska
Re: Please advice on homemade dive plateform can I JB cold weld glue
Steve
the syntax here is [img ] (space added to allow string to display) closed by [/ img] (space added, again). That set of characters will call a correctly structured URL of a located/online/stored image file and display that image file's content her in the phpBB software driven Forum; there are a couple posts on this in the recent past.
The BB software doesn't use the full string [image] that I've seen? So the posts you've made - would have to edited to the correct string of characters from [image] to [img]- to be interpreted to display the linked images, as near as I'm aware? I don't work in support of the site but those strings shown in your posts seem to suggest they're not being identified as instructional- they're being displayed just as text.
Pictures would help a lot- since I read your post and wasn't able to get a clear picture of the question being asked? As a general rule of thumb- I've not heard anyone, except in jest, suggest epoxies as an accepted method of joining aluminum, in my experience welding or mechanical fasteners are the only proven methods of fabrication.
Cheers,
Kevin Morin
Kenai, AK
the syntax here is [img ] (space added to allow string to display) closed by [/ img] (space added, again). That set of characters will call a correctly structured URL of a located/online/stored image file and display that image file's content her in the phpBB software driven Forum; there are a couple posts on this in the recent past.
The BB software doesn't use the full string [image] that I've seen? So the posts you've made - would have to edited to the correct string of characters from [image] to [img]- to be interpreted to display the linked images, as near as I'm aware? I don't work in support of the site but those strings shown in your posts seem to suggest they're not being identified as instructional- they're being displayed just as text.
Pictures would help a lot- since I read your post and wasn't able to get a clear picture of the question being asked? As a general rule of thumb- I've not heard anyone, except in jest, suggest epoxies as an accepted method of joining aluminum, in my experience welding or mechanical fasteners are the only proven methods of fabrication.
Cheers,
Kevin Morin
Kenai, AK
kmorin
-
- Posts: 22
- Joined: Wed Mar 01, 2017 8:31 am
- 7
Re: Please advice on homemade dive plateform can I JB cold weld glue
I plan to have a removeable dive plateform.
it overlaps engine POD,bolton angle surport against transom.
two tubes surport outside this where I want to continue the removeable option.
it overlaps engine POD,bolton angle surport against transom.
two tubes surport outside this where I want to continue the removeable option.
Last edited by Steve the Brain on Thu Oct 18, 2018 7:17 am, edited 1 time in total.
-
- Posts: 22
- Joined: Wed Mar 01, 2017 8:31 am
- 7