I have a Garmin GHP Reactor autopilot on my North River RAIV with the course computer (heading sensor) mounted below the deck, under the helm area. It works but I’m not able to get very good compass calibration values. Am I fighting a losing battle with a metal boat or should I be looking for other sources of magnetic interference?
Ethan
NRB Almar 28 RAIV
Heading sensor on alloy boat
-
- Donator 23
- Posts: 27
- Joined: Thu Nov 13, 2014 2:36 pm
- 9
- Your location: Boston, MA
- Location: Coastal Massachusetts
-
- Doator '08, '09, '10, '11, '12, '13, '14, '15, '16, '17
- Posts: 177
- Joined: Tue Mar 24, 2009 7:12 pm
- 15
- Your location: Gulfport, Fl
Re: Heading sensor on alloy boat
Is it consistent or all over the place? Alloy should not be the culprit. Some thing ferrous or electromagnetic. Not all stainless steel types are non magnetic if there are any near. Also on the center line of the boat is best.
"It was the Law of the Sea, they said. Civilization ends at the waterline.
Beyond that, we all enter the food chain, and not always right at the top."
Hunter S. Thompson
Beyond that, we all enter the food chain, and not always right at the top."
Hunter S. Thompson
-
- Donator 23
- Posts: 27
- Joined: Thu Nov 13, 2014 2:36 pm
- 9
- Your location: Boston, MA
- Location: Coastal Massachusetts
Re: Heading sensor on alloy boat
I’m not sure, I’ll have to experiment some more. It’s primarily the Garmin autopilot Calibration Value in the Dealer Setup menu which concerns me. It’s gives a number from 0 to 100, with 100 being a magnetically perfect environment. Mine is somewhere around the mid 50s and I think needs to be much higher.
-
- Contributor
- Posts: 486
- Joined: Wed Jan 09, 2008 12:59 am
- 16
- Your location: Brisbane, Australia
- Location: Brisbane, Australia
Re: Heading sensor on alloy boat
Do you have electric wiring near the sensor? This can cause magnetic interference. One reason why the compass light wires should always be twisted to negate any interference which will affect the compass heading.
If there are hot wires in the vicinity a quick test is to turn off the power if this is possible & check the calibration value. If there is wiring & it is house feed you can wire a smaller battery directly to your panel buss & turn off your house feed then check the calibration.
Alloy is not magnetic so my money is on the wiring.
If there are hot wires in the vicinity a quick test is to turn off the power if this is possible & check the calibration value. If there is wiring & it is house feed you can wire a smaller battery directly to your panel buss & turn off your house feed then check the calibration.
Alloy is not magnetic so my money is on the wiring.
Regards,
Pete in Brisbane
Pete in Brisbane
-
- Donator 23
- Posts: 27
- Joined: Thu Nov 13, 2014 2:36 pm
- 9
- Your location: Boston, MA
- Location: Coastal Massachusetts
Re: Heading sensor on alloy boat
Here's the installation below the floor of the helm area, looking aft. I guess I have to admit that the course computer being only a few inches away from the bilge pump wires is probably not good.
Ethan
Ethan
- gandrfab
- Posts: 601
- Joined: Fri Mar 28, 2008 12:33 pm
- 16
- Your location: Edgewater Fl
- Location: Edgewater Fl
Re: Heading sensor on alloy boat
Just because I haven't seen the addressed.
Are you calibrating the compass on the water underway?
Are you calibrating the compass on the water underway?
-
- Doator '08, '09, '10, '11, '12, '13, '14, '15, '16, '17
- Posts: 177
- Joined: Tue Mar 24, 2009 7:12 pm
- 15
- Your location: Gulfport, Fl
Re: Heading sensor on alloy boat
There is probably magnets in the motor. There are shielding materials. Mu-metal foil might work to shield magnetic interference.
Mu metal is a nickel–iron soft magnetic alloy with very high permeability suitable for shielding sensitive electronic equipment against static or low frequency magnetic fields. It has several compositions. One such composition is approximately 77% nickel, 16% iron, 5% copper and 2% chromium or molybdenum.
Mu metal is a nickel–iron soft magnetic alloy with very high permeability suitable for shielding sensitive electronic equipment against static or low frequency magnetic fields. It has several compositions. One such composition is approximately 77% nickel, 16% iron, 5% copper and 2% chromium or molybdenum.
"It was the Law of the Sea, they said. Civilization ends at the waterline.
Beyond that, we all enter the food chain, and not always right at the top."
Hunter S. Thompson
Beyond that, we all enter the food chain, and not always right at the top."
Hunter S. Thompson
-
- Donator 23
- Posts: 27
- Joined: Thu Nov 13, 2014 2:36 pm
- 9
- Your location: Boston, MA
- Location: Coastal Massachusetts
Re: Heading sensor on alloy boat
Yes, underway calibration. I tried the calibration procedure again yesterday with no better results. At this point it's just an exercise in futility since the autopilot is working reasonably well even with the poor compass calibration value. I'll just make do with things as is.
- gandrfab
- Posts: 601
- Joined: Fri Mar 28, 2008 12:33 pm
- 16
- Your location: Edgewater Fl
- Location: Edgewater Fl
Re: Heading sensor on alloy boat
Next question (because I don't know) does the unit have or need a magnetic compass?
I haven't helped install, set up a autopilot in years they were Tr-1's.
The compass/gyro, heading sensor was a ball we mounted low on the hull CL mid ship. cough-cough glassboats
Setting them up even in semi rough water was not fun at all.
Consensus was to set them up on very calm days or take them inland to a lake.
And they set up just like the book said they would. Good luck.
Once set the roughest of seas we ever needed to boat in would not phase the autopilot.
I haven't helped install, set up a autopilot in years they were Tr-1's.
The compass/gyro, heading sensor was a ball we mounted low on the hull CL mid ship. cough-cough glassboats
Setting them up even in semi rough water was not fun at all.
Consensus was to set them up on very calm days or take them inland to a lake.
And they set up just like the book said they would. Good luck.
Once set the roughest of seas we ever needed to boat in would not phase the autopilot.