AluminumAlloyBoats.com

Next week starts the Seattle Boat Show. It runs from 27th thru the 5th Feb.Any one else going? Any interest for a beer at the Pyramid Brewery? I plan on being there for a day or two or three depending on free tickets I receive. One day I will spend a few hours selling Jim's Break away Flashers by QCove at Sportco's booth

John you gonna come to the Portland Sportsman Show the 8th-12th? I would like to make the Seattle show but I have too much work to get done before the Portland Show.

Mike

John:

I plan to attend Friday and Saturday. (1/27-8) Should I plan a dogleg to the Pyramid Brewery?

-tom

goatram wrote:Next week starts the Seattle Boat Show. It runs from 27th thru the 5th Feb.Any one else going? Any interest for a beer at the Pyramid Brewery? I plan on being there for a day or two or three depending on free tickets I receive. One day I will spend a few hours selling Jim's Break away Flashers by QCove at Sportco's booth

Where you gettin the FREE tickets? And what are you selling? I like the brewery too!

Anne and I are in, John. We may not be spending the night this time, but we'll be there. I am all about hitting the Pyramid!!!

Friday I have a invite by one of the Aluminum Boat Sellers aka Three Rivers Marine. Then Ken aka Flasher has one for me as well He is selling his QCove "Jim's Breakaway Flasher" At the Sportco Booth right across from where Stabicraft had their dispaly last year in the Hallway.

Saturday the 28th at 4 pm at the Pyramid?

Yes Les Pictures will be takin I THINK

Mike I have not made plans yet. I will think about it thou.

Oh yeah, pyramid brewskis . . . John, you feeling good enough already to be hiking around that big-BACK SIDE show?

Bob
We shall see!. I am feeling better if I have a whole day of walking in me I am to find out.

who's pushing Goats wheel chair, or carrying his walker up any steps? Don't forget if ya put new fuzzy tennis balls on the end of the legs, you can push it ahead of you as you scuff along........

C'mon

On a serious note <<<<<<really>>>>>>>?

My fishing buddy ole Doc Miller (68 yrs young) had a hip replaced in late Oct. and was on my boat fishing and in his own boat fishing by Christmas. And we don't pussy foot around, we be serious inshore fisherman,

I am a non complaint patient at times I see the Doc on Friday We shall see what he has to say.

Dave You been Lurking on the Red Site Reeeeeeellllllly Bloodydecks is contagious as you have found out Cmon. LURKER
You sound a lot like Marlin Mike in your post above

> Saturday the 28th at 4 pm at the Pyramid?

Good with me. Anyone else?

I'm heading down with a guide buddy of mine for the day on Monday. Meeting up with goatram and checking out Tower Todd's tuna seminar. Staying the night and hitting a few tackle stores Tuesday morning and heading back to Canuckville. Totally stoked to meet goatram and hopefully quite a few other folks. Should be a great trip !!!

Mike
Ken aka Flasher and I will be going to the Portland show on Thursday 9 Feb. He to look at it for his QCove Flashers and I to see the show and Meet up with you. I will have a pattern of my aft gunnel for a quote for the cleaning table tackle station riser. Be cause of the Self Bailing deck I raised the floor 4.5"; Me being 6'3" I want the table set to my height to clean fish.

As to the Seattle Show 4 pm at the brewery for a meet and greet. I am going to the Sportsman show in the morning as it stands now. The Appointment with the doc on Friday might change the morning plans but not the afternoon one.

Saturday at the show and later the Pub works for me @ 1600hrs. Capt PJ

I will be there all day with my son, and will meet you all at the Pyramid at 1600!!

A few pictures

That was it, two boats? Sportman's show down south is likely better for alloy . . . ?

Wish Bevan would bring a boat sometime, that would perk things up.

I will be posting some (maybe lots)pics as soon as I size them down and sort out the badun's...here is one of Russ (if wrong, pls correct me) at Coldwater and the thin sturctural model...very cool. Had a good conversation! Capt PJ

No Bob there are a lot more aluminum boats there. I am not done taking pictures as I am heading back tomorrow with John aka Sculpin23.

Pete that is a cool little boat model Hopefully Russ will stop by and explain it better. It was cut out of .020" SHEAT 1/5 SCALE using their cut plan shrunk down. All of the sheet pieces required for a big build where cut and delivered to the shop. The thin sheet is real hard to weld up without warping

Thank guys! I look forward to more (hopefully lots more) pictures.
I know posting pics is time consuming and a PITA but I , for one, really appreciate it.

As I write this I am loading bunches onto Photobucket...it is going to take some time. I would like to say that I had a good time talking with the dealers as I didn't get to meet many factory guys...I was impressed with the knowledge of the Stabilcaft sales staff and of course Coldwater. The others I spoke with it seemed I knew more about their boats then they did...just a general observation and based solely on who I talked to which was not all.

Had a good meet and greet at the Pyrimid, good food and good talk...goatram will surely jump in and say who all was there as honestly the first time meeting I don't remember everyone's name and association..sorry it is just that way!

Well let's see if can post some more pics! Capt PJ

here are some interesting bait and cleaning stations, rod holder systems and bait tank tops.









Rod holders on ALUMWELD, I think! Capt PJ

I found this posted on the bulletin board of one of the brokers.




Looks like a nice cruiser for the go slow crowd needing comfort and economy and being ALLOY!!! Capt PJ

Bullfrog has an alloy hull...didn't know that...with HDPE topsides...interesting!




Compare with Stabicraft.





Capt PJ

Silver Streak at 70K




Capt PJ